2024-2026 For BMW 5 Series G60 Standard Front Lip

Front Lip Splitter for BMW 5 Series G60 / G61 (Standard Bumper), 2024-2026

The G60 5 Series has a long, upright nose that looks clean but visually tall in the lower bumper area. This three-piece front lip splitter sits under the standard front bumper and adds a horizontal line across the bottom of the car, which drops the visual ride height without touching the suspension, the springs or the warranty.

The splitter follows the existing lower bumper contour rather than sitting on top of it, so the panel gaps stay even from the centre section out to both corners. It is moulded in ABS rather than fiberglass, which means it flexes instead of cracking if you clip a steep driveway, and it is supplied with the mounting hardware and pre-applied automotive tape so it can be fitted in a driveway with hand tools.

Design and Construction

• Three-piece design: centre blade plus left and right corner extensions, so each section follows the bumper radius instead of pulling away at the corners.
• Moulded ABS construction — impact resistant and repairable, unlike fiberglass or carbon overlay parts that shatter on contact.
• Gloss black is a finished, polishable surface; carbon fiber style is a hydro-dipped pattern over the same ABS shell, not a bare carbon layup.
• Pre-drilled mounting points line up with the factory lower bumper fasteners, so no template is required.
• Pre-applied 3M-grade double-sided tape along the leading edge holds the lip in position while the mechanical fasteners are tightened.
• Adds approximately 25 mm of forward projection at the centre, enough to be visible in profile without reducing ground clearance at the axle line.

Vehicle Compatibility

This listing covers the standard (non M Sport) front bumper only. The table below lists the exact vehicle this part was tooled for.

Fitment is body-style specific. Read the exclusions below before ordering — the wrong bumper style is the most common return reason for this part.

• Does NOT fit G60 / G61 cars with the M Sport or M Performance front bumper — the bumper corners are a different shape. Order the M Sport version of this lip instead.
• Does NOT fit the previous generation G30 / G31 / G38 (2017-2023) or the F10 / F11 (2010-2016). The bumper radius and mounting points are completely different.
• Does NOT fit the BMW M5 (G90) or M5 Touring (G91), which use wider M-specific bumper geometry.
• Does NOT fit cars fitted with an aftermarket front bumper, front parking sensor relocation kit or a front tow-hook cover that changes the lower valance profile.

Chassis codes G60 (sedan) and G61 (Touring) share the same standard front bumper, which is why this lip is listed for both. The Chinese-market long-wheelbase G68 uses the same front end and is covered by the same part. If your car has the M Sport package, the bumper carries larger side intakes and a deeper centre section — that is a different part.

Specifications

What Is in the Box

• 1 x three-piece front lip splitter in the selected finish
• 1 x set of self-tapping screws and mounting clips
• 1 x roll of promoter wipes for the tape surfaces
• 1 x installation instruction sheet (English)

Installation Notes

1. Wash and degrease the lower front bumper. Any wax or road film left on the surface will make the tape release within days.
2. Test fit all three sections without removing the tape backing and check the panel gaps against the bumper corners.
3. Peel the backing from the centre section, press it into position and hold for 60 seconds.
4. Fit the left and right corner extensions, checking that the seam between sections stays tight.
5. Drive the self-tapping screws through the pre-drilled holes into the factory lower bumper fasteners. Do not over-torque — the ABS will crack around an over-tightened screw.
6. Leave the car dry for 24 hours before driving at highway speed so the adhesive reaches full bond strength.

Finish, Care and Expectations

Gloss black is a painted finish and can be polished, sealed and waxed like body paint. Carbon fiber style is a hydro-dipped pattern under a clear coat: it cannot be sanded or compounded, because sanding cuts through the pattern and leaves a grey patch. Wash both finishes with a pH-neutral shampoo and a soft mitt, and avoid automatic brush washes.

The part is supplied as a rigid ABS shell. Small scuffs on the underside are normal on a lowered front end and can be touched up with gloss black paint. If you regularly use a steep driveway or a car wash with a raised guide rail, approach at an angle — the splitter sits roughly 25 mm further forward than the stock bumper.

Shipping and Handling

Packed in a double-wall carton with foam corner blocks and a protective film over the finished face. Ships from our US warehouse within one business day; transit is typically 2-5 business days for the continental United States. We do not ship this item to freight forwarders, and we cannot combine it with oversized body panels in the same carton.

Why Buy From EliteGermanParts

Every part in this catalog is selected for one generation of BMW only. We publish the chassis code, the exact model years and the body-style exclusions on the product page instead of a vague "fits most 5 Series" claim, because a 2024 G60 bumper is not the same shape as a 2019 G30 bumper. If you are unsure which version your car takes, send us the last seven characters of your VIN and a photo of the bumper you are fitting and we will confirm the correct part before you order.

Parts are stored and shipped from our own warehouse, inspected for warping and cracked gel coat before packing, and protected with foam corner blocks and a double-wall carton. Orders placed before 2:00 PM Eastern on a business day leave the same day. If a part arrives damaged, send photographs of the carton and the part within 48 hours and we will replace it.