2024-2026 For BMW 5 Series G60 M Sport MP Style Front Lip

MP Style Front Lip Splitter for BMW 5 Series G60 / G61 M Sport, 2024-2026

The M Sport front bumper on the G60 already has the deeper centre intake that the standard car does not, but the lower edge still finishes flat. This MP style front lip adds the missing lower splitter line, extends the bumper forward at the centre and ties the two side intakes together visually.

This is the M Sport specific tooling. The corner geometry follows the larger M Sport side intakes rather than the standard bumper, so the lip meets the bumper edge without the gap that appears when a standard-bumper lip is forced onto an M Sport car. Moulded in ABS with a finished gloss black or hydro-dipped carbon fiber style surface.

Design and Construction

• Tooled specifically for the G60 / G61 M Sport front bumper — not a universal lip with slotted holes.
• Aggressive lower blade with raised centre section and sculpted side wings that follow the M Sport intake shape.
• Moulded ABS shell: flexible enough to survive kerb contact, rigid enough to hold its shape at speed.
• Gloss black is a painted, polishable finish; carbon fiber style is a hydro-dipped pattern under clear coat.
• Pre-drilled holes match the factory lower bumper fasteners; tape along the leading edge holds alignment during fitment.
• Ships as a single assembled blade with the corner sections keyed into the centre, so the seam stays tight.

Vehicle Compatibility

This listing covers the M Sport / M Performance front bumper only. Standard-bumper cars need the standard version of this lip.

Fitment is body-style specific. Read the exclusions below before ordering — the wrong bumper style is the most common return reason for this part.

• Does NOT fit G60 / G61 cars with the standard or Luxury Line front bumper — the corners will not meet the bumper edge. Order the standard version instead.
• Does NOT fit the previous generation G30 / G31 / G38 (2017-2023) or F10 / F11 (2010-2016), including their M Sport variants.
• Does NOT fit the BMW M5 (G90) or M5 Touring (G91) — M-specific bumper geometry is wider again.
• Does NOT fit cars with the M Performance carbon exterior package where the lower bumper already carries an OEM splitter.

The M Sport front bumper is identifiable by the larger, darker side intake inserts and the deeper centre section. If your car has body-colour side intakes with a horizontal blade, it is the standard bumper and this part will not fit. Chassis codes G60 (sedan), G61 (Touring) and the Chinese-market G68 long-wheelbase share this M Sport front end.

Specifications

What Is in the Box

• 1 x MP style front lip splitter in the selected finish
• 1 x set of self-tapping screws and mounting clips
• 1 x roll of promoter wipes for the tape surfaces
• 1 x installation instruction sheet (English)

Installation Notes

1. Degrease the lower M Sport bumper, paying attention to the inside of the side intake pockets where dust collects.
2. Test fit the blade and confirm both corner sections sit flush against the intake edges before removing any tape backing.
3. Peel the tape backing from the centre outward and press the blade into position, working from the middle to the corners.
4. Fit the self-tapping screws through the pre-drilled holes into the factory fasteners. Tighten by hand until the ABS just contacts the bumper.
5. Check the gap along the leading edge with a light behind the car; adjust before the adhesive fully cures.
6. Keep the car dry for 24 hours before highway driving.

Finish, Care and Expectations

Gloss black can be polished and sealed like body paint. Carbon fiber style is a hydro-dipped pattern under clear coat and must never be sanded or compounded — sanding removes the pattern and leaves a visible grey patch. Use a pH-neutral shampoo and a soft wash mitt, and avoid brush car washes.

Because this lip projects further forward than the stock M Sport bumper, take steep driveways at an angle and be aware of parking blocks. Light scuffs on the underside are normal and can be touched up with gloss black paint; damage to the finished face is best repaired by a body shop rather than a rattle can.

Shipping and Handling

Packed in a double-wall carton with foam corner blocks and a protective film over the finished face. Ships from our US warehouse within one business day; transit is typically 2-5 business days for the continental United States. We do not ship this item to freight forwarders.

Why Buy From EliteGermanParts

Every part in this catalog is selected for one generation of BMW only. We publish the chassis code, the exact model years and the body-style exclusions on the product page instead of a vague "fits most 5 Series" claim, because a 2024 G60 bumper is not the same shape as a 2019 G30 bumper. If you are unsure which version your car takes, send us the last seven characters of your VIN and a photo of the bumper you are fitting and we will confirm the correct part before you order.

Parts are stored and shipped from our own warehouse, inspected for warping and cracked gel coat before packing, and protected with foam corner blocks and a double-wall carton. Orders placed before 2:00 PM Eastern on a business day leave the same day. If a part arrives damaged, send photographs of the carton and the part within 48 hours and we will replace it.